Exactly how to Replace a Bath Tub (Step By Step).
Exactly how to Replace a Bath Tub (Step By Step).
Blog Article
Have you been on the lookout for guidance concerning Tools You Need to Install a New Bathtub ?
Setting up a bath tub isn't precisely brain surgery, but it does call for solid plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old tub with a brand-new one is also a reasonably difficult job. If the old bathtub is conveniently available, the job can relocate rapidly; if you need to open a wall to get rid of the old tub as well as place the new tub, the job is much harder. In either case, the job is within a residence handyman's skills, although you will certainly require a helper to leave the old bathtub and also set in the new one. See to it you have qualified on your own for the task and also are comfortable attempting it. As opposed to working with a professional to take control of a halfway-completed project, it is much better to take into consideration using one before you start. Opportunities are you may need an expert plumber to make tube links.
This article will aid you install a new tub in your washroom if you have currently acquired a new tub and also do not require to transform the setup of your previous water supply pipes.
Your tools as well as product list need to consist of the following:
Removing Old Touches
If you require to replace old taps with new ones as a part of your setup, after that the first thing you need to do is disconnect the supply of water. After doing so, switch on the taps to drain any type of water continuing to be in the system. The procedure of getting rid of the existing taps can be quite problematic because of the limited accessibility that is usually the instance.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipes to the taps. Have a fabric prepared for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will have to be cleaned of any old sealing substance.
Prior to going on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the new taps. If the old taps are longer than the new faucets, after that a shank adapter is required for the new taps to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet and also the various other end supplies a connection to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly need minimizing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin guaranteeing that the washing machines remain in location between the faucet and also the sink. Protect the tap in place with the manufacturer given backnut. When the tap is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal faucet ports. The former type needs to be linked to the tap finishes initially, tightening only by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.
Setting up the Bathtub
Making use of the two wood boards under its feet, put the bath tub in the needed position. The wood boards are useful in equally spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 little factors.
The next objective is to guarantee that the bath tub is leveled all round. This can be accomplished by examining the spirit level and also changing the feet on the bath tub until the level reads degree.
To install faucets, fit all-time low of the furthest adaptable tap port to the appropriate supply pipeline by making a compression sign up with; then do the very same for the other faucet.
Activate the supply of water and also check all joints and also new pipework for leaks and also tighten them if necessary. Fill up the bath tub as well as also inspect the overflow electrical outlet and the typical electrical outlet for leaks.
Lastly, deal with the bathroom paneling as explained in the maker's instruction manual. Tiling as well as securing around the bath tub ought to wait up until the bath tub has been utilized at the very least once as this will resolve it right into its final position.
Getting ready for the Installment
Firstly, the supporting structure supplied with the bath must be fitted (if called for) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is very important to see to it that if the tap includes a plastic washing machine, it is fitted between the bath as well as the taps. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the taps system to stop strain on the bathtub.
Fit the flexible tap connectors to the bottom of the two taps utilizing 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you make use of every one of the provided washers.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom ought to now be ready to be suited its last setting.
Tiling Around the Tub
In the area where the bath fulfills the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is necessary as the installation can relocate enough to fracture a stiff seal, causing the water to penetrate the wall in between the bathroom as well as the tiling, resulting in problems with dampness and feasible leakages to the ceiling below.
You can choose from a variety of coloured sealers to assimilate your components as well as fittings. They are marketed in tubes and also cartridges, as well as are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a larger void to load, you can fill it with twists of soaked paper or soft rope. Keep in mind to always fill the bath tub with water prior to sealing, to permit the activity experienced when the tub is in usage. The sealer can break fairly very early if you do not think about this activity prior to sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also conveniently offered on the market. It is suggested to fit the ceramic tiles utilizing water-resistant or waterproof glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm certainly very inquisitive about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I am praying you appreciated the new article. Sharing is caring. You just don't know, you may be helping someone out. I treasure reading our article about Installing A Bathtub.
Visit Our Website Report this page